15 49.0138 8.38624 1 1 5000 https://www.1154lill.com 300 true 0
theme-sticky-logo-alt

Connecting a gas stove: how to install a gas stove step by step

It is hardly possible to imagine at least one kitchen without a cooking stove. Due to a number of distinctive characteristics and advantages, it is gas stoves that are most common. However, their use must be treated especially responsibly in order to avoid dangerous situations..

It is hardly possible to imagine at least one kitchen without a cooking stove. Due to a number of distinctive characteristics and advantages, it is gas stoves that are most common.

It is hardly possible to imagine at least one kitchen without a cooking stove. Due to a number of distinctive characteristics and advantages, it is gas stoves that are most common..

Features of the correct connection of the gas stove

The operation of a gas stove always begins with its installation. Next, we will talk about how to properly connect a gas stove.

Is it possible to install a gas stove yourself?

The question of whether you can install a gas stove yourself is the most common one. The installation of any gas equipment in an apartment must be approved by the gas distribution organization. This is required by the rules established by the Government of the Russian Federation. By law, you cannot independently replace and connect gas stoves in an apartment. This should be done by specialists from specialized companies after the conclusion of a maintenance and repair contract..

According to the law, it is impossible to independently replace and connect gas stoves in an apartment, this should be done by specialists.

According to the law, it is impossible to independently replace and connect gas stoves in an apartment, this should be done by specialists.

Roughly the same is the case with Gazprom Mezhregiongaz. In accordance with the supply contract, the client is responsible for reporting changes that are related to gas equipment. According to these standards, the connection of gas stoves should be dealt with by a gas distribution specialist..

According to these standards, the connection of gas stoves must be dealt with by a GDO specialist.

According to these standards, the connection of gas stoves should be dealt with by a gas distribution specialist..

What documents are needed to install gas equipment

It is impossible to proceed with the installation of a gas stove without the availability of appropriate documentation. To sign a contract for the supply of gas to a house and open a personal account with the gas service, you need to prepare a package of documents. It includes:

• a certificate of state registration of a residential property and a certificate of ownership rights (purchase and sale agreement, deed of donation);

• contract for the maintenance of gas equipment in the apartment;

• old subscriber book (if available);

• passport for the device, which takes into account the gas consumption;

• technical passport for the dwelling.

After filling in all the points in the forms and reading the briefing on the operation of gas equipment, a gas supply contract is signed and a permit for installation work is issued.

After filling in all the points in the forms and reading the briefing on the operation of gas equipment, a gas supply contract is signed and a permit for installation work is issued.

This documentation is submitted to the gas service for verification, after which a subscription book and special forms for registration of a contract are issued. After filling in all the points in the forms and reading the briefing on the operation of gas equipment, a gas supply contract is signed and a permit for installation work is issued.

Connection tools and parts

In order for the connection to be made correctly, you need to prepare the necessary tools and parts:

• flexible hose of the required length – universal – about 1.5 m, or individual rubber – from 1 m or more;

• ball valve made of nickel-plated brass;

• gas and adjustable wrenches;

• gasket – as a rule, it comes with the stove;

• various screwdrivers;

• sealing tape or thread – FUM-tape or thread Loktayl 55 will do;

• a soapy solution of medium concentration and a brush, you will need to check the correct connection.

How the installation works

The hardware installation process consists of several important stages. Let’s consider each of them in detail.

Seat selection

The first step is to choose a suitable place to install the stove. A level floor surface will ensure a level installation, which will avoid uneven cooking due to a skewed hob.

Many modern models have leveling feet. They allow you to install the stove evenly, even if the floor in the apartment is far from ideal..

The first step is to choose a suitable place to install the stove.

The first step is to choose a suitable place to install the stove..

Additional Information!

You can install the equipment exactly using the building level.

If the unit does not have such legs, then you can use thick cardboard as a lining, a piece of chipboard or a wooden plank.

Important!

The back of the slab must not come into contact with the supporting structures.

During installation, it is necessary to provide free access to all connecting nodes, so that in case of leaks or malfunctions, the problem can be eliminated as soon as possible..

Also, at the back of the slab, you need to leave a small gap between the wall. As a rule, the recommended size of such a gap is indicated in the instructions for the technique..

During installation, it is necessary to provide free access to all connecting nodes so that in the event of a leak or malfunction, the problem can be eliminated as soon as possible.

During installation, it is necessary to provide free access to all connecting nodes so that in the event of leaks or malfunctions, the problem can be eliminated as soon as possible..

Dismantling the old slab

1. First of all, you need to turn off the gas valve and check if the gas flow has stopped.

2.Unscrew the lock nut from the lowering of the gas pipe.

3. The slab must be moved away from the wall..

4. The squeegee is unscrewed from the device using a key.

Additional Information!

If the new stove will not be installed immediately, then it is better to put a plug below the tap..

Replacing the tap

First you need to unscrew the old tap without removing it completely. The window must be wide open, as a small gas leak will have to be allowed during the valve change. In advance, you need to prepare a piece of cloth and wet it. After that, we rip off the old tap, and twist the hole with a wet cloth to ensure gas shutoff.

Next, we prepare the thread. It should be free of rust, paint, glue and debris. A sealing tape is wound around the thread. After that, the plug is removed from the fabric and a new tap is screwed on..

The faster the tap is turned on, the less leakage will be. It is important that there are no open flames or sparks in the kitchen..

First you need to unscrew the old tap without removing it completely.

First you need to unscrew the old tap without removing it completely.

Installing a new plate

The gas hose must be of high quality and reliable – you cannot save on it. The outlet to the stove must match the hose.

A sealing tape must be wound on the external thread of the fitting. You need to check the thread in advance. Next, the fitting is screwed into the lowering ball valve. Then you can screw the gas hose into the thread of the gas stove..

After the installation is complete, you need to check the correctness of the connection again..

The gas hose must be of high quality and reliable - you cannot save on it

The gas hose must be of high quality and reliable – you cannot save on it

Hob connection

1. After releasing the equipment from the packaging, you need to leave only a protective film, which will not allow the plate to get dirty during installation..

2. You need to pay attention to the documents: information about the required gap between the wall and the unit should be displayed there.

3. Using a building level, you need to check the level position of the working surface. If the stove is not level, you can adjust the height using the twisting feet or, if they are not available, use improvised pads..

4. The seal must be wound on the place of the threaded connection of the gas pipeline and the flexible hose..

5. The hose must be connected to the drop below the tap using a suitable wrench..

6. During this connection it is important to remember that the gasket must also be installed. As a rule, it is included in the package. This device extends the life of the gas stove, as it retains various debris..

7. Finally, check if all connections are tight enough..

8. Check the tightness.

Video: Connecting a gas stove

Electric ignition connection

In modern technology, electric ignition is very common, but it must also be connected following safety precautions. You must have a modern grounded outlet. The grounding function can be performed by the built-in neutral wire – this is the case in any new model of household appliances.

Electric ignition can be mechanical or automatic, but this does not matter during the connection process. When self-installing the stove, the first gas supply must still be controlled by a specialist.

In modern technology, electric ignition is very common, but it must also be connected following safety precautions.

In modern technology, electric ignition is very common, but it must also be connected, following safety precautions..

Features of connecting the stove to a gas cylinder

Gas cylinders are used today only in rural areas. The connection of such cylinders has its own characteristics..

1. There should be a minimum distance of 1.5 meters between the cylinder and the plate itself. If it is possible to place cylinders not in a living room in a metal box, then this will be an ideal option..

2. The room must have a good ventilation system. Gas pressure in cylinders is much higher than in a gas pipeline. For this reason, it is imperative to use a reduction gear..

Features of connecting the stove to a gas cylinder

Features of connecting the stove to a gas cylinder

Connection process.

1. A gas hose is connected to the stove. For tightness, a sealant or special sealant is used.

2. The other end of the hose is connected to the reducer.

3. Connect the reducer to the cylinder in a horizontal position..

4. At the end, it is imperative to check the connections to avoid possible leaks. When lighting the burner, there should be no soot or bluish flashes..

Video: The process of connecting a gas stove

Checking for correct connection

You can check if the connection was made correctly with a soapy solution. It is necessary to coat the joints with them, after which the tap is opened. When sealed, there should be no bubbles. If they still appear, you will have to untwist and re-carry out the procedure for connecting the hose and winding the seal.

You can check if the connection was made correctly with a soapy solution.

You can check if the connection was made correctly using a soapy solution..

You can also familiarize yourself with such a device as a dielectric insert. It is necessary in order to prevent the negative effects of stray currents. This is especially true in apartment buildings, where it is impossible to know for sure that someone may have a leakage of current through the gas riser from an ungrounded household appliance. Such currents can seriously damage the electrical components of the unit. The dielectric insert prevents currents from passing through the metal braid of the flexible hose to the plate itself.

It is necessary in order to prevent the negative effects of stray currents.

It is necessary in order to prevent the negative effects of stray currents..

Additional Information!

A flexible rubber-fabric hose without a braid does not by itself allow the passage of electric current.

The dielectric insert is installed between the tap and the flexible hose. The threaded connection between them must also be sealed and checked..

After that, the tightness of the connection is checked in the previously described way..

The dielectric insert is installed between the tap and the flexible hose.

The dielectric insert is installed between the tap and the flexible hose.

Responsibility for self-connecting the gas stove

If the connection of the gas equipment was made unauthorized, then the following sanctions can be obtained.

1. The supplier disconnects the apartment from the lines until a fee of 35 thousand rubles for installing a gas stove and 45 thousand for installing a column is charged.

2. For citizens, an administrative penalty is provided in the form of a fine – 2 thousand, for officials – 3-4 thousand, for organizations and enterprises – up to 40 thousand rubles.

3. Criminal punishment provides for a penalty of imprisonment for up to two years for individuals.

4. If unauthorized installation resulted in the death of people – imprisonment for up to five years.

The consequences of improper installation of equipment can be very serious and sad, and therefore you should not neglect the established rules..

The consequences of improper installation of equipment can be very serious and sad, and therefore do not neglect the established rules.

The consequences of improper installation of equipment can be very serious and sad, and therefore you should not neglect the established rules..

Tips from the masters

Summing up, it is worth recalling once again the safety rules and mandatory standards..

1. The flexible hose that connects the equipment to the gas supply system must be placed in an accessible, unobstructed place.

2. The dimensions of the gas hose must fully comply with generally accepted regulatory documents.

3. The connecting sleeve must not be painted, as paint may crack and damage the surface. Self-adhesive paper can be used for a more aesthetic appearance..

4. The adapter should only be used if one of the outputs has a non-standard threaded connection..

5. Before proceeding with the installation of the stove, it is necessary to turn off the gas by turning the shut-off valve all the way. All those present in the room must be notified that work is underway on the installation of gas equipment.

6. When installing gas equipment, you must use only the tools designed for this..

Video: Tips for connecting a gas stove and oven

Using the materials of this article and the recommendations of professionals, you will avoid problems with regulatory authorities, and the use of technology will be as safe as possible..

Previous Post
Banyo tasarımı – fayans
Next Post
Nursery in a marine style with a photo for boys: decor features